Film presentation of the materials used after laying the tiles, porcelain tiles. Are only technologically very advanced materials and methods of application and installation.

Technology are the following aspects:
A. Leveling screeds achieve ultrafast or rapid drying which is mounted porcelain tiles
- Types of materials used and methods of implementing equalization screeds, semi-dry consistency (consistency because the mixture can be used dig and dig the slope role balconies or terraces pools), with very short drying time and high mechanical strength, shrinkage. Due to rapid drying and high compressive strength dig these types of equalization, is an ideal substrate that can be made ceramic tiles, natural stone cladding, etc.. Two mortar are two types of binders for screeds.
Two. Adhesives fast setting cement for installation of tiles
- Types of bicomponent adhesive cement, rapid setting and hardening, with great grip. Adhesives can be applied to the nominal thickness of 10 mm. Adhesives are suitable for carrying out hard and heavy traffic floors using that type of plates: porcelain tiles, Klinker, granite, marble, etc.. Are two types of adhesives.
Three. The joints of cement, rapid setting and hardening
Presentation putty cement setting and fast setting for filling rigid joints between tiles. Wide putty is used for grouting joints get stiff clad ceramic tiles, porcelain tiles, Klinker, mosaic glass ceramics or rigid joints of the plates covering ornamental stone - marble, granite, travertine, limestone, andesite, onyx, alabaster plates artificial stone or tile blended with polyester resin as a binder, artificial stone tiles tiles blended with the cement binder.
Four. Grouting elastic
Presents a two-component epoxy-polyurethane sealant, fluid consistency, applied by casting, with high resistance to abrasion, suitable for heavy traffic floors and hard elastic grouting ceramic tiles.


Features:
Leveling screed - Leveling screeds based on cement applied mechanically or manually. MAPEI leveling screeds are distinguished by the fact that: you can pour in thickness from 3-8 cm applied flotation (separation layer) or can be poured in thickness from 1-8 cm applied in bonding (with a primer of bonding) with the substrate, the mixture is semi-dry consistency and thus can give a slope easily applied mortar, not contractions and therefore does not crack, dry out very quickly, after only 1-4 days (depending on material used) reach humidity of 2% CM measured with carbide hygrometer and therefore suitable as a substrate that must be carried out quickly finishing. Provision of the hoe provides two special types of cement mixed with sand and two types of mortar (mix only with water). Compressive strength at 28 days are between 30 and 62 N / mm.

* Used on floors with embedded heating system, the coating over the heating pipes should be at least 25 mm and are reinforced with welded net required. This heating system can start after only four days from 21-28 days but require a traditional cement screed.
Used as slope ** quick drying screed on balconies, terraces, pools, fountains or wetlands on it, after only 24 hours apply a waterproofing elastic cement that is compatible with Class C2 adhesive ceramic tiles.

Cementitious adhesives, Fast setting - are adhesive performance, fast setting and hardening (the plywood can go after only 3 hours), with high adhesion, having measured the bond strength (28 days)> 2.5 N / mm and 22 N / mm in compression. Adhesives can be applied to the nominal thickness of 10 mm. Adhesives are suitable for carrying out hard and heavy traffic floors using that type of plates: porcelain tiles, Klinker, granite, marble, etc..

The joints of cement, rapid setting and hardening
Materials used for filling rigid joints between ceramic tiles, natural stone or composite stone is cement mortar (CG).
- Differentiation of joint sealants cement is based on the setting time, the width of the joints and thus the thickness of the final appearance of the surface resistance and grouted.
Ultracolor Plus has the features:
- DropEffect ®, because of Waterproofing additives, water is not absorbed in the mortar, and remains, the surface fish, in the form of drops. As a result, the joint surface is more resistant to dirt and easier to clean the joint.
- BioBlock ® consists in introduction of organic particles homogeneously distributed in the microstructure of mortar for plasters, to prevent the growth of microorganisms responsible for mildew.
- Short curing (20-30 minutes), the floor is grouted surface foot traffic quickly (3 hours) and putting into plating is fast (max 24 hours). Resistance after 3 o'clock, the compression is 12 N / mm.
- The joints has resistance to compression and abrasion. Final compressive strength is 30 N / mm.
- Not in any way aditiveaza latex (synthetic resin containing liquid) is formed as one.
- Not sun bright colors are pastel and not create incongruous with plywood.
- Color stability is studied over time.

Grouting elastic
Elastic grouting material used is a two component epoxy-polyurethane, fluid consistency that dries to become elastic. It is an extremely resistant to abrasion, chemicals and intensive wash. Suitable for joints flexible, high traffic floors, covered with any type of tile.

Substrate Preparation - screeds, Mapei line.
For additional information see the following materials and data sheets:

Binders and mortars for screeds equalization
Cement leveling screed drying ultrafast Mapecem
Drying leveling screed mortar ultrafast Mapecem Pronto
Cement quick drying leveling screed Topcem
Mortar quick drying leveling screed Topcem Pronto


Adhesives based fast-setting cement, trowel line.

Fast-setting adhesives, cement, improved fast setting (C2F)
Porcelain tiles and tile adhesive substrates Granirapid (EN) - PDF (C2F) / S1
Porcelain tiles and tile adhesive substrates Elastorapid (EN) - PDF (C2FTE) / S2
Porcelain tiles and tile adhesive substrates Keraquik (C2FT) / S1
 

Chituri de rosturi si etansanti elastici, Linia MAPEI.
For additional information see the following materials and data sheets:

Joints kits cement (CG)
Chit rosturi placi ceramice Ultracolor (GB) - PDF
Chit rosturi placi ceramice Keracolor FF
Chit rosturi placi ceramice Keracolor GG
Latex Fugolastic pentru chiturile pe baza de ciment Keracolor

Etansanti poliuretanici
Etansant rosturi elastice Mapeflex PU55 SL
Etansant rosturi elastice Mapeflex PU50 SL
Etansant rosturi elastice Mapeflex PU21
Etansant rosturi elastice Mapeflex PU30


Produse complementare, Linia MAPEI.
For additional information see the following materials and data sheets:

Detergent pentru chituri pe baza de ciment
Detergent placi ceramice si piatra naturala Keranet

Detergent/solvent pentru chituri pe baza de rasini epoxidice sau epoxi-poliuretanice
Solvent Pulicol